Solar equipment on a house, a block of flats, or on a building within the property boundary
Placing solar panels on the roof of your house or flat, or on a building within the grounds of your house or flat, is considered in most cases ‘Permitted Development’ (The Town and Country Planning (General Permitted Development) (England) Order 2015 – Schedule 2, Part 14), whether this is in a conservation area or otherwise.
This means that in general there is no need to seek planning permission from your Local Planning Authority (LPA) to proceed, subject to certain conditions. These conditions are:
- equipment on a building should be sited, so far as is practicable, to minimise the effect on the external appearance of the building and the amenity of the area
- when no longer needed equipment should be removed as soon as reasonably practicable
- if solar equipment is to be installed on a flat roof on Article 2(3) land then the developer must apply to the local planning authority for prior approval
If the property is part of a block of flats, all the following limits must be met:
- on a pitched roof, panels should not be installed above the highest part of the roof (excluding the chimney)
- panels should project no more than 200mm from the wall surface, or where relevant, the roof slope
- on a flat roof the highest part of the solar PV equipment cannot be more than 600mm higher than the highest part of the roof (excluding chimney)
- the panels must not be installed on a building that is within the grounds of a listed building or on a site designated as a scheduled monument
- if your property is in a conservation area, or in a World Heritage Site, panels must not be fitted to a wall which fronts a road
- in the case of plug-in solar, any part of the solar equipment should not be installed on a wooden wall, balcony or enclosure, or any exterior clad in timber
If the property is a house, all the following limits must be met:
- on a wall, balcony or roof enclosure which abuts a road, the solar PV should not protrude more than 0.2 metres beyond the plane of the wall, on any other wall, balcony or roof enclosure, it should not protrude by more than 0.4 metres
- on a pitched roof, panels should not be installed above the highest part of the roof (excluding the chimney) and should project no more than 200mm from the roof slope
- on a flat roof the highest part of the solar PV equipment cannot be more than 600mm higher than the highest part of the roof (excluding chimney)
- the panels must not be installed on a building that is within the grounds of a listed building or on a site designated as a scheduled monument
- if your property is in a conservation area, or in a World Heritage Site, panels must not be fitted to a wall, balcony or roof enclosure which fronts a road
- in the case of plug-in solar, any part of the solar equipment should not be installed on a wooden wall, balcony or enclosure, or any exterior clad in timber
If there is any doubt regarding compliance, it is recommended that you apply to your LPA for pre-application planning advice or a lawful development certificate (LDC) before starting works.
Where conditions cannot be met, or where your LPA has issued an ‘Article 4’ direction covering the area in which your property is located (Article 4 directions are made when the character of an area of acknowledged importance would be threatened - there is only one conservation area in Wirral to have an Article 4 Direction and that is Bromborough Pool.), an application for planning permission will be required.
Stand-alone solar equipment (panels not on a building but within the grounds of a house or a block of flats)
Placing solar panels on the grounds of a house or a block of flats, is considered in most cases ‘Permitted Development’ (The Town and Country Planning (General Permitted Development) (England) Order 2015 – Schedule 2, Part 14), whether this is in a conservation area or otherwise.
This means that in general there is no need to seek planning permission from your Local Planning Authority (LPA) to proceed, subject to certain conditions. These conditions are:
- stand-alone solar equipment should be sited, so far as is practicable, to minimise its effect on the amenity of the area
- when no longer needed equipment should be removed as soon as reasonably practicable
- if solar equipment is to be installed in a conservation area, closer to the road than the nearest part of the house or flats, then the developer must apply to the local planning authority for prior approval
- if solar equipment is to be installed on article 2(3) land, within 5 metres of the boundary of the curtilage, then the developer must apply to the local planning authority for prior approval
If the property is part of a block of flats, all the following limits must be met:
- only the first stand-alone solar installation will be permitted development. Further installations will require planning permission
- no part of the installation should be higher than four metres
- in a conservation area, where the solar equipment will be installed closer to the road than the nearest part of the flats, the equipment should not be higher than 2 metres
- the installation should be at least 5m from the boundary of the property
- the size of the array should be no more than 9 square metres or 3m wide by 3m deep
- panels should not be installed within boundary of a listed building or a scheduled monument
- if your property is in a World Heritage Site, no part of the solar installation should be nearer to any road bounding the block of flats than the part of the block of flats that is nearest to that road
- in the case of plug-in solar, any part of the solar equipment should not be installed on a wooden fence, gate, wall or other means of enclosure
If the property is a house, all the following limits must be met:
- no part of the stand-alone solar should exceed the lowest applicable height below:
- 1 metre in height, when within 5 metres of the boundary and situated on land forward of the principal elevation of the house
- 2 metres in height, when installed within 5 metres of the boundary
- 2 metres in height, when installed on land in a conservation area and nearer to any road bounding the house than the part of the house that is nearest to that road
- In any other case, 4 metres in height
- if your property is in a World Heritage Site, the installation should be at least 5m from the boundary of the property, and no part of the solar installation should be nearer to any road bounding the house than the part of the house that is nearest to that road
- any part of the stand-alone solar should not be installed within boundary of a listed building or a scheduled monument
- the size of the array should be no more than 9 square metres
In the case of plug-in solar, any part of the solar equipment should not be installed on a wooden fence, gate, wall or other means of enclosure.
If there is any doubt regarding compliance, it is recommended that you apply to your LPA for pre-application planning adviceOpens a new window or a lawful development certificateOpens a new window (LDC) before starting works.
Where conditions cannot be met, or where your LPA has issued an ‘Article 4’ direction covering the area in which your property is located (Article 4 directions are made when the character of an area of acknowledged importance would be threatened - there is only one conservation area in Wirral to have an Article 4 Direction and that is Bromborough Pool.), an application for planning permission will be required.
What could I consider when installing solar PV panels?
Make sure your building is as energy-efficient as possible, such as using insulation and draught-proofing. Find out more on the Energy Saving Trust website
For more information relating to Historic Buildings and energy efficiency, visit the Historic England website.
Key design considerations
Wirral Council is supportive of solar panel development where there is careful consideration for the protection of the heritage assets.
We recommend that applicants consider the proposed design and location of solar panel development:
- firstly consider installing the panels on the rear of a building so they are less visually prominent, in an angled frame on a flat roof, or on a modern detached building such as an extension, outbuilding or a garage. If this is not viable then consider the main roof of the house
- small-scale freestanding solar arrays that are well screened in enclosed gardens or closely linked to existing buildings within the curtilage of the property may be more preferable and less visually intrusive. Although this option is likely to require planning permission, it may have benefits because ground mounted panels are likely to be less obtrusive with no or minimal visual impact, easier to maintain, and have less impact on Wirral’s historic and traditional buildings
- where possible, use non-shiny materials that integrate well with the existing roof, such as a matte black colour
- site the installation to match the position of windows or other similar features on the existing building or surrounding buildings
- when choosing where to site the panels, try to minimise their effect on the external appearance of the building and on the amenity of the area
- remove the panels as soon as reasonably practicable when no longer needed
Listed buildings
If your house or flat is a listed building you must also apply for listed building consent.
With the installation of solar panels on a listed building, pre-application advice should be sought in the earliest stages of the proposal. In some cases, they will also need planning permission. The listed status of the building means additional care and consideration is required in the placement of the panels. This will ensure that the character or appearance of the listed building is not harmed. In some cases, they will not be permitted.
Before considering solar panels, it is best to improve the energy efficiency of the building in other ways to get the best out of the investment. Further advice can be found on the Historic England website.
Building regulations
If you wish to install solar panels on your roof, building regulations will normally apply. The ability of the existing roof to carry the load (weight) of the panels will need to be checked and proven. Some strengthening work may be needed. Building regulations also apply to other aspects of the work such as electrical installation.
Installers who are members of a relevant competent person scheme can self-certify certain types of building work, including the installation of solar PV, avoiding the need to seek separate building regulations approval. You are advised to check your installer is a member of a scheme covering the work they will be undertaking.
Solar Together Wirral
Wirral Council is working with Liverpool City Region Combined Authority (LCRCA) through the Climate Emergency initiative to reduce the region’s carbon emissions. Solar Together is a group-buying scheme, which brings households together to get high-quality solar panels at a competitive price.